Why Understanding Essential Plumbing Skills is Crucial For Installing a Bathtub
Why Understanding Essential Plumbing Skills is Crucial For Installing a Bathtub
Blog Article
How do you really feel in relation to How to Install a Bathtub Yourself?
Setting up a bath tub isn't precisely brain surgery, however it does need strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately difficult project. If the old tub is conveniently available, the task can move easily; if you have to open a wall surface to remove the old tub and position the brand-new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. See to it you have certified on your own for the job and also fit trying it. Instead of working with a professional to take over a halfway-completed project, it is better to take into consideration employing one before you start. Opportunities are you may need an expert plumber to make tube connections.
This article will assist you mount a brand-new bathtub in your washroom if you have currently bought a new bathtub and also don't need to change the setup of your previous water system pipes.
Your tools and also material checklist need to make up the following:
Getting ready for the Setup
First of all, the supporting structure provided with the bath ought to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps system to avoid strain on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its last position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite problematic due to the restricted gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have actually been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the required position. The wooden boards are handy in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bathtub up until the spirit level reviews degree.
To set up faucets, fit the bottom of the furthest flexible tap port to the ideal supply pipeline by making a compression sign up with; then do the very same for the other tap.
Switch on the water supply and check all joints and also brand-new pipework for leakages and also tighten them if required. Load the bath tub and also examine the overflow outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bathtub should wait till the tub has been used a minimum of once as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in area between the faucet and also the sink. Protect the faucet in position with the supplier supplied backnut. When the tap is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal tap connectors. The previous type should be connected to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a stiff seal, triggering the water to permeate the wall surface between the bath and the tiling, leading to difficulties with moisture as well as possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and fittings. They are marketed in tubes and also cartridges, as well as can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can fracture rather very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece of writing about How to Install a Bathtub when perusing the search engines. Sharing is nice. Helping others is fun. I am grateful for your time. Don't hesitate to pay a visit to our blog back soon.
Leading emergency plumbing services available. Report this page